What makes that powerful chainsaw cut so smoothly through tough wood? The secret often lies in a small but mighty part: the chain. A dull or incorrect chain can turn a quick job into a frustrating struggle, leaving you with sore arms and uneven cuts. Choosing the right chainsaw chain is more complicated than just grabbing the first one you see. You face confusing terms like “pitch,” “gauge,” and “drive link count.” Getting these wrong means your saw won’t fit, it will run poorly, or worse, it could become dangerous.
This guide cuts through the confusion. We break down the essential measurements so you can confidently match the perfect chain to your saw and your task. By the end of this post, you will understand exactly what you need for fast, safe, and efficient cutting every single time. Let’s dive into the anatomy of the chainsaw chain and unlock your saw’s true power.
Top Chain Saw Chains Recommendations
- 【SPECIFICATIONS】 3 Pack 18 Inch, 3/8" LP Pitch, .050" Gauge, 62 Drive Links, semi-chisel. This saw chain met the kickback performance requirements of ANSl B175.1-2012 when tested according to the provisions of ANSl B175.1-2012. Low kickback saw chain meets the kickback performance requirements of CSA Standard Z62.3.
- 【FIND YOUR CHAIN】Check the owner's manual or the guide bar side stamp to find the PITCH, GAUGE, LENGTH and DRIVE LINK NUMBER and select the chain according to these parameters. You are also welcome to contact the KAKEI Customer Support with the chainsaw/bar part number, we are always ready to assist you. (Visit the KAKEI Store for all 60+ sizes)
- 【Features】 Germany steel with heating temperature control and punching system make better toughness, Flatness. All saw chain rivets hardened and quenched, resists wear and improves strength, reducing chain tension changes.
- 【Features】Japanese chrome-plated technology creates better durability for cutters, and each of them was grinded and cold-headed with Rotary machines, becomes sharper than ever.
- Saw chain comes with protective oil, resists corrosion.
- 𝗩𝗘𝗥𝗜𝗙𝗬 𝗙𝗜𝗧: This saw chain is for chainsaw models that run 3/8" low-profile pitch, .050" (1.3 mm) gauge (guide bar slot), 62 drive links, 18" (45cm) bar and fits chainsaws up to 42cc - DOUBLE CHECK THE CHAINSAW MANUAL & VERIFY THE FIT
- 𝗙𝗜𝗧𝗦 𝗧𝗛𝗘𝗦𝗘 𝗖𝗛𝗔𝗜𝗡𝗦𝗔𝗪 𝗠𝗢𝗗𝗘𝗟𝗦: Atlas 56937, Craftsman CMXGSAMCN4218, S185, ECHO CS310, Ego CS1800, CS1804, Greenworks GCS80420, Husqvarna 240, 120 Mark II
- 𝗙𝗜𝗧𝗦 𝗧𝗛𝗘𝗦𝗘 𝗖𝗛𝗔𝗜𝗡𝗦𝗔𝗪 𝗠𝗢𝗗𝗘𝗟𝗦: Homelite ZR43100, Masterforce 2000094ME, Poulan PR4218, Remington RM1645, Ryobi RY3818, RY40580, RY40580, Sun Joe SWJ701E, and more
- 𝗟𝗢𝗪 𝗞𝗜𝗖𝗞𝗕𝗔𝗖𝗞: Bumper drive link paired with depth gauge design, offers reduced kickback with strong performance
- 𝗢𝗥𝗘𝗚𝗢𝗡 𝗤𝗨𝗔𝗟𝗜𝗧𝗬: The original pioneer and inventor of modern saw chain since 1947. Designed and engineered in the USA.
- Chain Specifications: 4 Pack 16 Inch Chainsaw Chain 3/8" LP Pitch .043'' Gauge 56 Drive Links.
- Compatible Brands: Fits most chainsaws brands that run 3/8 Inch Pitch, .043 Inch (1.1 mm) gauge, 56 drive links. Fits Milwaukee, EGO, DeWalt, Greenworks, Makita , Poulan, Craftsman, etc.
- Smooth Cutting: High toughness, heat-treated semi-chisel chain cuts smoothly with a higher tolerance for debris. Low-kickback, low-vibration chain helps reduce user fatigue and allows consistent cuts.
- Wear Resistant: Premium industrial hard chrome outer layer helps reduce wear and chain adjustments for better durability. Hardened rivets provide a stronger connection between chain links, adding strength and withstanding loads.
- Note: Please verify your parameters to ensure this chain fits your chainsaw.
- 𝗩𝗘𝗥𝗜𝗙𝗬 𝗙𝗜𝗧: This saw chain is for chainsaw models that run 3/8" low-profile pitch, .050" (1.3 mm) gauge (guide bar slot), 56 drive links, 16" (40cm) bar and fits chainsaws up to 42cc - DOUBLE CHECK THE CHAINSAW MANUAL & VERIFY THE FIT
- 𝗙𝗜𝗧𝗦 𝗧𝗛𝗘𝗦𝗘 𝗖𝗛𝗔𝗜𝗡𝗦𝗔𝗪 𝗠𝗢𝗗𝗘𝗟𝗦: Craftsman/Sears 358.34116, 358.35161, 358.35170, 358.35514, 358.38070, 358.38160, 38.38170, Echo (only when used with Oregon branded bars) CS-310, CS-330T, CS-346, CS-352, CS-355T, CS-360T, CS-370, CS-400, CS-3400, CS-3450
- 𝗙𝗜𝗧𝗦 𝗧𝗛𝗘𝗦𝗘 𝗖𝗛𝗔𝗜𝗡𝗦𝗔𝗪 𝗠𝗢𝗗𝗘𝗟𝗦: Husqvarna 136*, 137*, 142*, 235E*, 240*, 240E*, 334T, 335T, 338XPT*, 339XP*, T435, T540XP (*Ensure your model has a 3/8” low profile sprocket), Greenworks 20022, 20232, CS60L210, CS60L00, CS80L211, and CS80L01
- 𝗟𝗢𝗪 𝗞𝗜𝗖𝗞𝗕𝗔𝗖𝗞: Bumper drive link paired with depth gauge design, offers reduced kickback with strong performance
- 𝗢𝗥𝗘𝗚𝗢𝗡 𝗤𝗨𝗔𝗟𝗜𝗧𝗬: The original pioneer and inventor of modern saw chain since 1947. Designed and engineered in the USA.
- WHY CHOOSE THESE CHAINS:5-Pack Value- Multiple replacements for long-term use.Smooth, fast cutting with minimal kickback for safety.
- UNIVERSAL COMPATIBILITY:Our chainsaw Chain Fits almost all 6-inch mini chainsaws (cordless/corded electric models).Seamless fit with 6-inch guide bars for smooth operation.Greenworks/RYOBI P25013BTL is not applicable.
- EASY INSTALLATION & ADJUSTMENT:Remove the side cover with a nut driver.Replace the old chain (ensure correct direction).Reattach the cover and adjust tension with a screwdriver.
- PREMIUM MATERIAL:Premium Manganese Steel Construction.Deeply quenched for extreme durability and high hardness.The service life of the saw chain is longer and smooth.
- SHARP TEETH:Perfect for garden pruning, firewood, bamboo, PVC pipes, and DIY projects. Sharp, wear-resistant teeth maintain efficiency over time.
- [ 4 PACK 8 INCH CHAIN] 3/8" LP Pitch .050" Gauge 33 Drive Links, please check the length and drive links. Suitable for most 8-inch pole saw. This saw chain met the kickback performance requirement of ANSI Standards
- [ REPLACEMENT FOR ]# S33, SG-S33, 63PM333E, 91EX033 91PJ033X 91PXL033G. FOR Greenworks Pole Saw 20192 Corded 6.5A, 20302 40V, 20612 20V Li-ION, 20352 24V Li-ION, 20672 40V Li-ION, 1400102 24V Li-ION. FOR Kobalt Pole Saw 506891 40V, KPS 80-06 40V, KPS 80-08, KSP 80-07. FOR Remington RM4050B, RM4050. FOR Portland 63190, 62896
- [ FITS MOST 8" POLE SAW ] This 8 inch replacement chains compatible with Chicago Pole Saw 68862. Sun Joe Pole Chainsaw models SWJ800E SWJ802E SWJ806E iON8PS pole saw. Earthwise CCS30008 Pole saw CPS40108, CPVS41008, LPS40208, PS40008. Harbor Freight, Portland, Kobalt, Remington and more pole saw chainsaws
- [ SHARP AND STRONG CHAIN ] This 8 inch chainsaw chain is deeply quenched to ensure smooth cutting and optimal lubrication. The service life of the saw chain is longer and smooth, lightweight, wear-resistant, and cuts smoothly
- [ EASY TO REPLACE ] Use a nut driver to open the side cover, replace the original chain and guide bar with ours, install the side cover and tighten the nut, then use a screwdriver to turn the screw to adjust the tightness of the chain. Please pay attention to the installation direction
Choosing the Right Chain Saw Chain: Your Essential Buying Guide
A chainsaw chain is the heart of your saw. A good chain cuts fast and lasts long. A bad chain causes trouble. This guide helps you pick the best one for your needs.
Key Features to Look For
Several important things make a chainsaw chain good or bad. You must check these before you buy.
1. Pitch
The pitch is the distance between the drive links. It measures how big your chain is. You must match the chain pitch exactly to your saw’s guide bar. Common pitches are 3/8-inch, .325-inch, and 1/4-inch. Check your saw’s manual for the correct size. Using the wrong pitch causes poor cutting and damages your saw.
2. Gauge
The gauge is the thickness of the drive link. This link fits into the groove on the guide bar. Common gauges are .050-inch, .058-inch, and .063-inch. Like the pitch, the gauge must match your bar groove perfectly. If the chain is too loose or too tight, it will not work safely.
3. Chain Type (Cutter Style)
Chains come in different cutter shapes. These shapes decide how fast and smooth the saw cuts.
- Full Chisel: These cutters are very sharp and square-shaped. They cut fast in clean wood. They dull quickly in dirt or knots.
- Semi-Chisel: These cutters have a rounded shape. They cut slightly slower than full chisel. They stay sharp longer in dirty conditions. They are great for general use.
- Low Profile: These small chains are often used on smaller, lighter saws.
4. Number of Drive Links
This is simply how many teeth make up the chain loop. This number must match the length of your specific guide bar. Always count the drive links on your old chain or check your bar markings to get the right length.
Important Materials and Durability
Chains must handle hard work. The material they use matters a lot for how long the chain lasts.
High-Quality Steel
Good chainsaw chains use hardened alloy steel. This steel resists wear and tear. Better quality chains use chrome plating on the cutting edges. This chrome plating makes the teeth much harder. Harder teeth stay sharp longer, even when cutting tough wood.
Rivets and Links
The rivets hold the chain pieces together. Strong, well-made rivets prevent the chain from stretching too fast or breaking apart under stress. Poorly made rivets are a weak spot.
Factors That Improve or Reduce Quality
Quality is not just about the steel; it is about how the chain is made.
Factors That Improve Quality:
- Precision Manufacturing: Chains made with tight tolerances cut better and vibrate less.
- Lubrication Features: Some chains have small oil holes on the drive links. These holes help carry oil to the bar groove, which reduces friction and heat.
- Filing Ease: A chain that is easy to sharpen correctly will perform better over its life.
Factors That Reduce Quality:
- Soft Metal: Chains made from cheap, soft steel dull very quickly. You will spend too much time sharpening.
- Poorly Set Bumpers: The small metal pieces between the cutters (depth gauges) must be set perfectly. If they are wrong, the chain will either cut too deep (dangerous) or not cut at all.
User Experience and Use Cases
Your job determines the best chain for you.
For Homeowners and Occasional Use
If you only trim a few branches yearly, a standard semi-chisel chain is perfect. It is forgiving and stays sharp enough between uses.
For Professional Loggers and Firewood Processing
Professionals need maximum speed. They should choose a full-chisel chain made from high-grade, chrome-plated steel. These chains require frequent, careful sharpening, but they offer the fastest possible cutting time.
For Cutting Old, Dirty Wood
When cutting wood with dirt, rocks, or heavy knots, always select a semi-chisel chain. The rounded cutters resist damage better than the sharp square edges of a full chisel.
10 Frequently Asked Questions (FAQ) About Chainsaw Chains
Q: How often should I sharpen my chainsaw chain?
A: You should check the sharpness before every use. If the saw starts pushing instead of cutting chips, or if you have to force the saw, it needs sharpening immediately.
Q: Can I use a chain for a different brand of saw?
A: Yes, if the pitch, gauge, and drive link count match exactly. Chain specifications are universal, not brand-specific.
Q: What is the purpose of the depth gauge (bumper)?
A: The depth gauge controls how much wood the cutter removes with each pass. It sets the cutting depth.
Q: Why is my new chain stretching?
A: All new chains stretch slightly as they break in. This is normal. You must re-tension the chain frequently during the first few uses.
Q: How do I measure my chain pitch?
A: Measure from the center of one rivet to the center of the next rivet, and multiply that measurement by two. Or, check your bar markings.
Q: Does oiling matter for the chain?
A: Yes! You must use bar and chain oil every time you run the saw. Oil prevents friction, heat buildup, and premature wear on the chain and bar.
Q: Should I buy a pre-sharpened or unsharpened chain?
A: Most new chains come pre-sharpened from the factory. It is often easier to buy a new, sharp chain than to try to sharpen a very dull one unless you have the right filing tools.
Q: What is the difference between a cutting tooth and a drive link?
A: The cutting tooth (cutter) does the actual cutting. The drive link sits below the cutter and fits into the bar groove, driving the chain forward.
Q: Can I mix different types of cutters on one chain?
A: No. You must use a consistent cutter style (all semi-chisel or all full chisel) across the entire loop for safe, balanced cutting.
Q: When should I replace the chain instead of sharpening it?
A: Replace the chain when the cutters are worn down so much that you cannot achieve the correct cutting angle even after filing. Also, replace it if the chain cracks or the rivets become loose.